SIDFEN ASL series Specifications

B550 & B700Operators Manual Isotech North America158 Brentwood Drive, Unit 4 Colchester, VT 05446 Phone: (802) 863-8050 Fax:

B550 & B700 Operator’s Handbook The controller can be set to tune its own P.I.D parameters. This is not normally necessary except when a greatly

B550 & B700 Operator’s Handbook There are two methods of tuning. Pre-tuning and self tuning, although the latter is not recommended as it can aff

B550 & B700 Operator’s Handbook Firstly the controller parameters need to be noted if they are different to the default ASL settings (for example

B550 & B700 Operator’s Handbook 3.9 Changing to 0.1°C Resolution Operation to Change from 1°C resolution (700°C maximum temperature) to 0.1°C res

B550 & B700 Operator’s Handbook 4. The Serial Interface for the controller (if fitted) The controller may be optionally fitted with an RS232 or

B550 & B700 Operator’s Handbook 5. Achieving the best results using your Metal Block Calibrator This section of your manual is written to help y

B550 & B700 Operator’s Handbook WARNING: Insertion of the incorrect probe type into these holes may result in inaccurate measurements and/or the

B550 & B700 Operator’s Handbook Figure 3. Recommended orientation for twin inserts. 5.5 Supply Voltage Variations As with all electrical equip

B550 & B700 Operator’s Handbook “B” or XMT - terminal Pins 14, 15 RS232 25 Way ‘D’ type socket T x D Pin 2 R x D Pin 3 GND Pin 7 CTS

B550 & B700 Operator’s Handbook The actual readings (Indictor reading) are ‘IN 01’ to ‘IN 17’. The system is then calibrated a second time and t

B550 & B700 Operator’s Handbook Table of Contents 1. INTRODUCTION...

B550 & B700 Operator’s Handbook InPUt 2tHEr3Pt1005dEG60.1C7Type4F2F2F1F2 F1F2F1F2 F1F2AL1AL1To next section of menu8EndAL1 F1SEtUP1F2dISPL9dECPO10

B550 & B700 Operator’s Handbook InPUt 2dISPL3CSLIn5AdC4F1F1F1AL1 F1SEtUP1F2Key pressDisplayFUn7F2F2F1OnF2POInt9F1F2In 1 10F1OU 111F2F2F2 Act

B550 & B700 Operator’s Handbook 7. Specifications 7.1 General Model Well Depth (mm) Well Dia. (mm) Insert Length (mm) Temperature range in normal

B550 & B700 Operator’s Handbook 8. Cleaning and Maintainance 8.1 Cleaning Make sure the Block Calibrator is turned off and unplug the mains suppl

B550 & B700 Operator’s Handbook 8.5 Periodic Maintenance WARNING The block calibrator should be checked every 2 years to have the safety

B550 & B700 Operator’s Handbook iii) The name of your purchasing and technical contact. iv) A brief fault report. 9.4 Repair Quotations We shall

B550 & B700 Operator’s Handbook 10. Appendix 1 Performance charts The graphs above, Figure 7 at 125°C and Figure 8 at 200°C, show the vertic

B550 & B700 Operator’s Handbook 11. Appendix 2 Wiring connections for DIN connector Figure 9. Wiring Diagram for Independent

B550 & B700 Operator’s Handbook 12. Appendix 3 Factory Settings Description Parameter B550 B700 RESOLUTION REQUIRED 1 0.1 1 0.1 1 1 Configurat

B550 & B700 Operator’s Handbook WARNING Read section 3.5 before altering the controller’s parameters, in particular the setpoint limits. Excee

B550 & B700 Operator’s Handbook 9. SERVICE AND WARRANTY...

B550 & B700 Operator’s Handbook NOTES B550-14-002 29 Issue 7

B550 & B700 Operator’s Handbook 1. Introduction Automatic Systems Laboratories would like to thank you for purchasing this B series Metal Block Ca

B550 & B700 Operator’s Handbook Figure 1. Model B550 with Independent Indicator vi) Do not use any liquid in the probe holes of the block. (

B550 & B700 Operator’s Handbook 2.3 Over temperature cut out ASL Metal Block Calibrators are fitted two independent over temperature cut outs whi

B550 & B700 Operator’s Handbook 3. Setting up the Calibrator The Calibrator is designed to give the best performance when operated in a constant

B550 & B700 Operator’s Handbook Auto/Manual Key Low Key High Key Function Key Figure 2. The Controller keys B550-14-002 7 Issu

B550 & B700 Operator’s Handbook Whilst operating, the controller will show two temperatures on the controller panel, and the supply switch will be